Impact of PbI2 Passivation and Grain Size Engineering in CH3NH3PbI3 Solar Absorbers as Revealed by Carrier‐Resolved Photo‐Hall Technique

With power conversion efficiencies now exceeding 25%, hybrid perovskite solar cells require deeper understanding of defects and processing to further approach the Shockley‐Queisser limit. One approach for processing enhancement and defect reduction involves additive engineering—, e.g., addition of MASCN (MA = methylammonium) and excess PbI₂ have been shown to modify film grain structure and improve performance. However, the underlying impact of these additives on transport and recombination properties remains to be fully elucidated. In this study, a newly developed carrier‐resolved photo‐Hall (CRPH) characterization technique is used that gives access to both majority and minority carrier properties within the same sample and over a wide range of illumination conditions. CRPH measurements on n‐type MAPbI₃ films reveal an order of magnitude increase in carrier recombination lifetime and electron density for 5% excess PbI₂ added to the precursor solution, with little change noted in electron and hole mobility values. Grain size variation (120–2100 nm) and MASCN addition induce no significant change in carrier‐related parameters considered, highlighting the benign nature of the grain boundaries and that excess PbI₂ must predominantly passivate bulk defects rather than defects situated at grain boundaries. This study offers a unique picture of additive impact on MAPbI₃ optoelectronic properties as elucidated by the new CRPH approach.     

Optimal Interfacial Engineering with Different Length of Alkylammonium Halide for Efficient and Stable Perovskite Solar Cells

Recently, two‐dimensional (2D) structure on three‐dimensional (3D) perovskites (graded 2D/3D) has been reported to be effective in significantly improving both efficiency and stability. However, the electrical properties of the 2D structure as a passivation layer on the 3D perovskite thin film and resistance to the penetration of moisture may vary depending on the length of the alkyl chain. In addition, the surface defects of the 2D itself on the 3D layer may also be affected by the correlation between the 2D structure and the hole conductive material. Therefore, systematic interfacial study with the alkyl chain length of long‐chained alkylammonium iodide forming a 2D structure is necessary. Herein, the 2D interfacial layers formed are compared with butylammonium iodide (BAI), octylammonium iodide (OAI), and dodecylammonium iodide (DAI) iodide on a 3D (FAPbI₃)_0.95(MAPbBr₃)_0.05 perovskite thin film in terms of the PCE and humidity stability. As the length of the alkyl chain increased from BA to OA to DA, the electron‐blocking ability and humidity resistance increase significantly, but the difference between OA and DA is not large. The PSC post‐treated with OAI has slightly higher PCE than those treated with BAI and DAI, achieving a certified stabilized efficiency of 22.9%.     

Strong Interplay between Sodium and Oxygen in Kesterite Absorbers: Complex Formation,Incorporation, and Tailoring Depth Distributions

Sodium and oxygen are prevalent impurities in kesterite solar cells. Both elements are known to strongly impact performance of the kesterite devices and can be connected to efficiency improvements seen after heat treatments. The sodium distribution in the kesterite absorber is commonly reported, whereas the oxygen distribution has received less attention. Here, a direct relationship between sodium and oxygen in kesterite absorbers is established using secondary ion mass spectrometry and explained by defect analyses within the density functional theory. The calculations reveal a binding energy of 0.76 eV between the substitutional defects Na_Cu and O_S in the nearest neighbor configuration, indicating an abundance of Na? O complexes in kesterite absorbers at relevant temperatures. Oxygen incorporation is studied by introducing isotopic ¹⁸O at different stages of the Cu₂ZnSnS₄/Mo/soda‐lime glass baseline processing. It is observed that oxygen from the Mo back contact and contaminations during the sulfurization are primary contributors to the oxygen distribution. Indeed, unintentional oxygen incorporation leads to immobilization of sodium. This results in a strong correlation between sodium and oxygen, in excellent agreement with the theoretical calculations. Consequently, oxygen availability should be monitored to optimize postdeposition heat treatments to control impurities in kesterite absorbers and ultimately, the solar cell efficiency.     

Direct Nanoscale Characterization of Deep Levels in AgCuInGaSe2 Using Electron Energy‐Loss Spectroscopy in the Scanning Transmission Electron Microscope

A new experimental framework for the characterization of defects in semiconductors is demonstrated. Through the direct, energy‐resolved correlation of three analytical techniques spanning six orders of magnitude in spatial resolution, a critical mid‐bandgap electronic trap level (E_V + 0.56 eV) within Ag_0.2Cu_0.8In_1?xGa_xSe₂ is traced to its nanoscale physical location and chemical source. This is achieved through a stepwise, site‐specific correlated characterization workflow consisting of device‐scale (≈1 mm²) deep level transient spectroscopy (DLTS) to survey the traps present, scanning probe–based DLTS (scanning‐DLTS) for mesoscale‐resolved (hundreds of nanometers) mapping of the target trap state's spatial distribution, and scanning transmission electron microscope based electron energy‐loss spectroscopy (STEM‐EELS) and X‐ray energy‐dispersive spectroscopy for nanoscale energy‐, structure, and chemical‐resolved investigation of the defect source. This first demonstration of the direct observation of sub‐bandgap defect levels via STEM‐EELS, combined with the DLTS methods, provides strong evidence that the long‐suspected Cu_In/Ga substitutional defects are indeed the most likely source of the E_V + 0.56 eV trap state and serves as a key example of this approach for the fundamental identification of defects within semiconductors, in general.     

Nanocomposite scaffold seeded with mesenchymal stem cells for bone repair

The mechanical property of bone tissue scaffolds is one of the most important aspects in bone tissue engineering that has remained problematic. In our previous study, we fabricated a three‐dimensional scaffold from nano‐hydroxyapatite/gelatin (nHA/Gel) and investigated its efficiency in promoting bone regeneration both in vitro and in vivo. In the present study, the effect of adding silicon carbide (SiC) on the mechanical and biological behaviors of the nHA/Gel/SiC and bone regeneration in vivo were determined. nHA and SiC were synthesized and characterized by the X‐ray diffraction pattern and transmission electron microscope image. Layer solvent casting, freeze drying, and lamination techniques were applied to prepare these scaffolds. Then, the biocompatibility and cell adhesion behavior of the synthesized nHA/Gel/SiC scaffolds were investigated. For in vivo studies, rats were categorized into three groups: blank defect, blank scaffold, and rat bone marrow mesenchymal stem cells (rBM‐MSCs)/scaffold. After 1, 4, and 12 weeks post‐injury, the rats were sacrificed and the calvaria were harvested. Sections with a thickness of 5 µm thickness were prepared and stained with hematoxylin–eosin and Masson's Trichrome, and immunohistochemistry was performed. Our results showed that SiC effectively increased the mechanical properties of the nHA/Gel/SiC scaffold. No significant differences were observed in biocompatibility, cell adhesion, and cytotoxicity of the nHA/Gel/SiC in comparison with the nHA/Gel nanocomposite. Based on histological and immunohistochemical studies, both osteogenesis and collagenization were significantly higher in the rBM‐MSCs/scaffold group, quantitatively and qualitatively. The present study strongly suggests the potential of SiC as an alternative strategy to improve the mechanical and biological properties of bone tissue engineering scaffolds, and shows that the pre‐seeded nHA/Gel/SiC scaffold with rBM‐MSCs improves osteogenesis in the engineered bone implant.     

Colorectal cancer and country of birth in New South Wales,Australia: All-of-population data for prioritising health service delivery and research

IntroductionCancer care and outcomes differ across cultural groups in Australia. Quantifying these differences facilitates prioritisation and targeting of services and research. All-of-population data are needed by health agencies to understand and fulfil their cancer-control responsibilities. Compiling these data can be challenging while maintaining privacy. We have used data linkage to gain population-wide colorectal cancer data on stage (degree of spread), treatment, and survival in New South Wales (NSW), Australia, by country of birth (COB), and consider service implications.MethodsWe studied colon and rectal cancers diagnosed in 2003–2016 and recorded on the NSW Cancer Registry (n = 41,575), plus linked hospital data and data from Australian Medical and Pharmaceutical Benefits payments, other treatment data and death records. Outcomes for 12 COB categories were analysed using multiple logistic and proportional hazards regression, with Australia as the reference category.ResultsCompared with Australian born, the adjusted odds ratio for distant spread of colon cancer was higher for people born in Lebanon and the United Kingdom. Treatment was less common for people born in China (surgery), Germany (systemic), Italy (surgery), New Zealand (any treatment) and Vietnam (all treatments), while treatment for rectal cancer was more common for people born in Italy (surgery), United Kingdom (radiotherapy, systemic therapy), and Vietnam (surgery), and less frequent for people born in China (radiotherapy). Adjusted 5-year survival was higher for people born in China, Italy, Vietnam, Greece (colon), Lebanon (colon) and other non-English speaking countries. More advanced stage was negatively related to having surgery and survival.ConclusionsThis study illustrates how linked data can enable comparisons of multiple outcomes for colorectal cancer by country of birth across an entire population. Results disclose “big picture” variations in population characteristics, stage, treatment and survival. This will enable better targeting and prioritisation of services and inform research priorities to address disparities.     

Mapping quantitative trait Loci underlying fitness-related traits in a free-living sheep population

We searched for quantitative trait loci (QTL) underlying fitness-related traits in a free-living pedigree of 588 Soay sheep in which a genetic map using 251 markers with an average spacing of 15 cM had been established previously. Traits examined included birth date and weight, considered both as maternal and offspring traits, foreleg length, hindleg length, and body weight measured on animals in August and jaw length and metacarpal length measured on cleaned skeletal material. In some cases the data were split to consider different age classes separately, yielding a total of 15 traits studied. Genetic and environmental components of phenotypic variance were estimated for each trait and, for those traits showing nonzero heritability (N= 12), a QTL search was conducted by comparing a polygenic model with a model including a putative QTL. Support for a QTL at genome-wide significance was found on chromosome 11 for jaw length; suggestive QTL were found on chromosomes 2 and 5 (for birth date as a trait of the lamb), 8 (birth weight as a trait of the lamb), and 15 (adult hindleg length). We discuss the prospects for refining estimates of QTL position and effect size in the study population, and for QTL searches in free-living pedigrees in general.     

Meltrin beta expressed in cardiac neural crest cells is required for ventricular septum formation of the heart

The heart is divided into four chambers by membranous septa and valves. Although evidence suggests that formation of the membranous septa requires migration of neural crest cells into the developing heart, the functional significance of these neural crest cells in the development of the endocardial cushion, an embryonic tissue that gives rise to the membranous appendages, is largely unknown. Mice defective in the protease region of Meltrin beta/ADAM19 show ventricular septal defects and defects in valve formation. In this study, by expressing Meltrin beta in either endothelial or neural crest cell lineages, we showed that Meltrin beta expressed in neural crest cells but not in endothelial cells was required for formation of the ventricular septum and valves. Although Meltrin beta-deficient neural crest cells migrated into the heart normally, they could not properly fuse the right and left ridges of the cushion tissues in the proximal outflow tract (OT), and this led to defects in the assembly of the OT and AV cushions forming the ventricular septum. These results genetically demonstrated a critical role of cardiac neural crest cells expressing Meltrin beta in triggering fusion of the proximal OT cushions and in formation of the ventricular septum.     

关节镜制备膝关节软骨缺损的动物模型

目的:经微创手术制备膝关节软骨缺损动物模型,减少因手术创伤造成对实验结果的影响。方法:关节镜下对9只山羊(9膝)进行关节面钻孔术,造成软骨缺损模型,对其缺损位置进行准确定位。结果:9只山羊(9膝)均在关节镜下顺利进行了关节软骨缺损模型的建立,并进行了缺损部位的定位。结论:对比开放性手术,经关节镜制备关节缺损模型是一种对实验干预最少的微创方法,有助于减少手术本身造成的实验误差。     

嗅鞘细胞复合PLGA导管修复周围神经缺损的研究

探讨嗅鞘细胞(OECs)复合聚乳酸-聚羟基乙酸共聚物(PLGA)导管对大鼠坐骨神经缺损的修复作用。方法:SD大鼠80只,随机分成4组,切除右侧部分神经干造成10mm的神经缺损。OECs PLGA组用充满细胞外基质凝胶和OECs悬液(CM-DiI预标记)的PLGA导管桥接坐骨神经缺损;OECs 硅胶管组用含相同内容物的硅胶管桥接;PLGA组和硅胶管组则分别用充满细胞外基质凝胶和DMEM/F12培养基的PLGA导管和硅胶管桥接。术后每周进行感觉运动功能检测,8周时行腓肠肌湿重恢复率、乙酰胆碱脂酶(AChE)染色、电生理和组织形态学分析等检测,同时移植细胞的两组每周进行细胞示踪观察。结果:移植细胞沿神经纵轴分布;除坐骨神经功能指数(SFI)指标外,OECs PLGA组的各项再生功能指标均优于其它三组。结论:OECs复合PLGA导管能够促进再生神经的成熟和靶组织功能的恢复,二者联合移植是一种有效的周围神经缺损修复方法。